Use $INTERFACE in example tinc-up scripts.

[wiki] / examples / ipv6-network.mdwn

diff --git a/examples/ipv6-network.mdwn b/examples/ipv6-network.mdwn
index 9ea6da4..653dc11 100644 (file)
--- a/examples/ipv6-network.mdwn
+++ b/examples/ipv6-network.mdwn
@@ -40,17 +40,15 @@ This document is to highlight an example setup for using tinc to create an IPv6
   * "routera" configuration for tinc (the master router):
 >      >cat tinc.conf
 >      Name = routera
->      Device=/dev/net/tun
->      TCPOnly = on
 >      Mode = switch
 >      Interface = vpn6
 >     
 >      >cat tinc-up
 >      #!/bin/sh
 >      #Enable tinc
->      ip -6 link set vpn6 up mtu 1280 txqueuelen 1000
->      ip -6 addr add 2001:db8:beef::1/64 dev vpn6
->      ip -6 route add 2001:db8:beef::/48 dev vpn6
+>      ip -6 link set $INTERFACE up mtu 1280 txqueuelen 1000
+>      ip -6 addr add 2001:db8:beef::1/64 dev $INTERFACE
+>      ip -6 route add 2001:db8:beef::/48 dev $INTERFACE
 >      #Static routing table
 >      ip -6 route add 2001:db8:beef:2::/64 via 2001:db8:beef::2
 >      ip -6 route add 2001:db8:beef:3::/64 via 2001:db8:beef::3
@@ -63,30 +61,28 @@ This document is to highlight an example setup for using tinc to create an IPv6
 >      ip -6 route del 2001:db8:beef:3::/64 via 2001:db8:beef:::3
 >      ip -6 route del 2001:db8:beef:4::/64 via 2001:db8:beef:::4
 >      #Disable tinc
->      ip -6 route del 2001:db8:beef::/48 dev vpn6
->      ip -6 addr del 2001:db8:beef::1/64 dev vpn6
->      ip -6 link set vpn6 down
+>      ip -6 route del 2001:db8:beef::/48 dev $INTERFACE
+>      ip -6 addr del 2001:db8:beef::1/64 dev $INTERFACE
+>      ip -6 link set $INTERFACE down
 >     
   * "routerb" configuration for tinc (the other non-master routers will be like this one):
 >      >cat tinc.conf
 >      Name=routerb
->      Device=/dev/net/tun
->      TCPOnly = yes
 >      Mode = switch
->      Interface = vpn6
 >      ConnectTo = routera
+>      Interface = vpn6
 >     
 >      >cat tinc-up
 >      #!/bin/sh
->      ip -6 link set vpn6 up mtu 1280
->      ip -6 addr add 2001:db8:beef::2/64 dev vpn6
+>      ip -6 link set $INTERFACE up mtu 1280
+>      ip -6 addr add 2001:db8:beef::2/64 dev $INTERFACE
 >      ip -6 route add default via 2001:db8:beef::1
 >     
 >      >cat tinc-down
 >      #!/bin/sh
 >      ip -6 route del default via 2001:db8:beef::1
->      ip -6 addr del 2001:db8:beef::2/64 dev vpn6
->      ip -6 link set vpn6 down
+>      ip -6 addr del 2001:db8:beef::2/64 dev $INTERFACE
+>      ip -6 link set $INTERFACE down
 
 5. You can use [radvd](http://www.litech.org/radvd/) or [Quagga](http://www.quagga.net/) to perform [stateless address autoconfiguration](http://www.ietf.org/rfc/rfc2462.txt) on your LAN. This is an example zebra.conf for LAN autoconfiguration (don't forget to enable the zebra daemon):
 >      ipv6 forwarding