From: Ivo Timmermans Date: Thu, 9 Nov 2000 21:29:58 +0000 (+0000) Subject: Updates, updates X-Git-Tag: release-1.0pre3~1 X-Git-Url: https://www.tinc-vpn.org/git/browse?p=tinc;a=commitdiff_plain;h=6e27618708233998db7e5886ed9afaa21bb9d938 Updates, updates --- diff --git a/doc/tinc.texi b/doc/tinc.texi index b51bf01a..d9105862 100644 --- a/doc/tinc.texi +++ b/doc/tinc.texi @@ -1,5 +1,5 @@ \input texinfo @c -*-texinfo-*- -@c $Id: tinc.texi,v 1.8.4.6 2000/11/02 21:34:45 zarq Exp $ +@c $Id: tinc.texi,v 1.8.4.7 2000/11/09 21:29:58 zarq Exp $ @c %**start of header @setfilename tinc.info @settitle tinc Manual @@ -17,7 +17,7 @@ Copyright @copyright{} 1998,199,2000 Ivo Timmermans , Guus Sliepen and Wessel Dankers . -$Id: tinc.texi,v 1.8.4.6 2000/11/02 21:34:45 zarq Exp $ +$Id: tinc.texi,v 1.8.4.7 2000/11/09 21:29:58 zarq Exp $ Permission is granted to make and distribute verbatim copies of this manual provided the copyright notice and this permission notice are @@ -42,7 +42,7 @@ Copyright @copyright{} 1998,1999,2000 Ivo Timmermans , Guus Sliepen and Wessel Dankers . -$Id: tinc.texi,v 1.8.4.6 2000/11/02 21:34:45 zarq Exp $ +$Id: tinc.texi,v 1.8.4.7 2000/11/09 21:29:58 zarq Exp $ Permission is granted to make and distribute verbatim copies of this manual provided the copyright notice and this permission notice are @@ -532,35 +532,14 @@ The actual setup of the ethertap device is quite simple, just repeat after me: @example -ifconfig tap@emph{n} hw ether fe:fd:@emph{xx}:@emph{xx}:@emph{xx}:@emph{xx} +ifconfig tap@emph{n} hw ether fe:fd:00:00:00:00 @end example -The @emph{n} here is the number of the ethertap device you want to use. -It should be the same @emph{n} as the one you use for -@file{/dev/tap@emph{n}}. The @emph{xx}s are four hexadecimal numbers -(0--ff). With previous versions of tincd, it didn't matter what they -were. But newer kernels require properly set up ethernet addresses. In -fact, the old behavior was wrong. It is required that the @emph{xx}s -match the numbers of the IP address you will give to the tap device and -to the MyOwnVPNIP configuration (which will be discussed later). - @cindex MAC address @cindex hardware address -@strong{Tip}: for finding out what the MAC address of the tap interface -should be, you can use the following command: - -@example -$ printf 'fe:fd:%02x:%02x:%02x:%02x' 10 1 54 1 -fe:fd:0a:01:36:01 -@end example - -or with perl: - -@example -$ perl -e 'print "fe:fd:", join(":", map @{sprintf "%02x", $_@} split(/\./, $ARGV[0])), "\n";' 10.1.54.1 -fe:fd:0a:01:36:01 -@end example - +@strong{Note:} Since version 1.0pre3, all interface addresses are set to +this address, whereas previous versions required the MAC to match the +actual IP address. @cindex ifconfig To activate the device, you have to assign an IP address to it. To set @@ -741,17 +720,20 @@ maskbits is the number of bits set to 1 in the netmask part. @item MyVirtualIP = This is an alias for MyOwnVPNIP. -@item Passphrases = (/etc/tinc/NETNAME/passphrases) -The directory where tinc will look for passphrases when someone tries to -connect. Please see the manpage for genauth(8) for more information -about passphrases as used by tinc. - @item PingTimeout = (5) The number of seconds of inactivity that tinc will wait before sending a probe to the other end. If that other end doesn't answer within that same amount of seconds, the connection is terminated, and the others will be notified of this. +@item PrivateKey = +This is a sequence of hexadecimal numbers, as generated by ``tincd +--generate-keys''. + +@item PublicKey = +This is a sequence of hexadecimal numbers, as generated by ``tincd +--generate-keys''. + @item TapDevice = (/dev/tap0) The ethertap device to use. Note that you can only use one device per daemon. The info pages of the tinc package contain more information