X-Git-Url: https://www.tinc-vpn.org/git/browse?p=tinc;a=blobdiff_plain;f=doc%2Ftinc.texi;h=af88c48a9a1f7a0d899408797c175a1e73cefcaf;hp=16229e53afb08052a51cf5e05158dcce1dc19e1c;hb=cf49b2c0647554613874cce495e4a7937a9f7863;hpb=2e159d0139e77041ad82e96bf0abef6aaf64a258

diff --git a/doc/tinc.texi b/doc/tinc.texi
index 16229e53..af88c48a 100644
--- a/doc/tinc.texi
+++ b/doc/tinc.texi
@@ -1,4 +1,5 @@
 \input texinfo   @c -*-texinfo-*-
+@c $Id: tinc.texi,v 1.8.4.8 2000/11/24 14:13:51 zarq Exp $
 @c %**start of header
 @setfilename tinc.info
 @settitle tinc Manual
@@ -16,6 +17,7 @@ Copyright @copyright{} 1998,199,2000 Ivo Timmermans
 <itimmermans@@bigfoot.com>, Guus Sliepen <guus@@sliepen.warande.net> and
 Wessel Dankers <wsl@@nl.linux.org>.
 
+$Id: tinc.texi,v 1.8.4.8 2000/11/24 14:13:51 zarq Exp $
 
 Permission is granted to make and distribute verbatim copies of this
 manual provided the copyright notice and this permission notice are
@@ -40,6 +42,8 @@ Copyright @copyright{} 1998,1999,2000 Ivo Timmermans
 <itimmermans@@bigfoot.com>, Guus Sliepen <guus@@sliepen.warande.net> and
 Wessel Dankers <wsl@@nl.linux.org>.
 
+$Id: tinc.texi,v 1.8.4.8 2000/11/24 14:13:51 zarq Exp $
+
 Permission is granted to make and distribute verbatim copies of this
 manual provided the copyright notice and this permission notice are
 preserved on all copies.
@@ -176,6 +180,10 @@ tinc will run on them as well.  Without this driver, tinc will most
 likely compile and run, but it will not be able to send or receive data
 packets.
 
+For a more up to date list, please check the list on our website:
+@uref{http://tinc.nl.linux.org/platforms.html}.
+
+
 @c ==================================================================
 @subsection Linux
 
@@ -382,6 +390,18 @@ build and install this package are included within the package.  Please
 make sure you build development and runtime libraries (which is the
 default).
 
+If you installed the OpenSSL libraries from source, it may be necessary
+to let configure know where they are, by passing configure one of the
+--with-openssl-* parameters.
+
+@example
+--with-openssl=DIR      OpenSSL library and headers prefix
+--with-openssl-include=DIR OpenSSL headers directory
+                        (Default is OPENSSL_DIR/include)
+--with-openssl-lib=DIR  OpenSSL library directory
+                        (Default is OPENSSL_DIR/lib)
+@end example
+
 
 @c
 @c
@@ -528,27 +548,14 @@ The actual setup of the ethertap device is quite simple, just repeat
 after me:
 
 @example
-ifconfig tap@emph{n} hw ether fe:fd:@emph{xx}:@emph{xx}:@emph{xx}:@emph{xx}
+ifconfig tap@emph{n} hw ether fe:fd:00:00:00:00
 @end example
 
-The @emph{n} here is the number of the ethertap device you want to use.
-It should be the same @emph{n} as the one you use for
-@file{/dev/tap@emph{n}}.  The @emph{xx}s are four hexadecimal numbers
-(0--ff). With previous versions of tincd, it didn't matter what they
-were.  But newer kernels require properly set up ethernet addresses.  In
-fact, the old behavior was wrong.  It is required that the @emph{xx}s
-match the numbers of the IP address you will give to the tap device and
-to the MyOwnVPNIP configuration (which will be discussed later).
-
 @cindex MAC address
 @cindex hardware address
-@strong{Tip}: for finding out what the MAC address of the tap interface
-should be, you can use the following command:
-
-@example
-$ printf 'fe:fd:%02x:%02x:%02x:%02x' 10 1 54 1
-fe:fd:0a:01:36:01
-@end example
+@strong{Note:} Since version 1.0pre3, all interface addresses are set to
+this address, whereas previous versions required the MAC to match the
+actual IP address.
 
 @cindex ifconfig
 To activate the device, you have to assign an IP address to it.  To set
@@ -729,17 +736,20 @@ maskbits is the number of bits set to 1 in the netmask part.
 @item MyVirtualIP = <local address[/maskbits]>
 This is an alias for MyOwnVPNIP.
 
-@item Passphrases = <directory> (/etc/tinc/NETNAME/passphrases)
-The directory where tinc will look for passphrases when someone tries to
-connect. Please see the manpage for genauth(8) for more information
-about passphrases as used by tinc.
-
 @item PingTimeout = <seconds> (5)
 The number of seconds of inactivity that tinc will wait before sending a
 probe to the other end. If that other end doesn't answer within that
 same amount of seconds, the connection is terminated, and the others
 will be notified of this.
 
+@item PrivateKey = <key>
+This is a sequence of hexadecimal numbers, as generated by ``tincd
+--generate-keys''.
+
+@item PublicKey = <key>
+This is a sequence of hexadecimal numbers, as generated by ``tincd
+--generate-keys''.
+
 @item TapDevice = <device> (/dev/tap0)
 The ethertap device to use. Note that you can only use one device per
 daemon. The info pages of the tinc package contain more information