\input texinfo @c -*-texinfo-*-
+@c $Id: tinc.texi,v 1.8.4.17 2001/05/25 10:06:13 guus Exp $
@c %**start of header
@setfilename tinc.info
@settitle tinc Manual
This is the info manual for tinc, a Virtual Private Network daemon.
-Copyright @copyright{} 1998,199,2000 Ivo Timmermans
+Copyright @copyright{} 1998-2001 Ivo Timmermans
<itimmermans@@bigfoot.com>, Guus Sliepen <guus@@sliepen.warande.net> and
Wessel Dankers <wsl@@nl.linux.org>.
+$Id: tinc.texi,v 1.8.4.17 2001/05/25 10:06:13 guus Exp $
Permission is granted to make and distribute verbatim copies of this
manual provided the copyright notice and this permission notice are
@page
@vskip 0pt plus 1filll
@cindex copyright
-Copyright @copyright{} 1998,1999,2000 Ivo Timmermans
+Copyright @copyright{} 1998-2001 Ivo Timmermans
<itimmermans@@bigfoot.com>, Guus Sliepen <guus@@sliepen.warande.net> and
Wessel Dankers <wsl@@nl.linux.org>.
+$Id: tinc.texi,v 1.8.4.17 2001/05/25 10:06:13 guus Exp $
+
Permission is granted to make and distribute verbatim copies of this
manual provided the copyright notice and this permission notice are
preserved on all copies.
@menu
* Introduction:: Introduction
-* Installing tinc - preparations::
-* Installing tinc - installation::
-* Configuring tinc::
-* Running tinc::
-* Technical information::
-* About us::
+* Preparations::
+* Installation::
+* Configuration::
+* Running tinc::
+* Technical information::
+* About us::
* Concept Index:: All used terms explained
@end menu
@contents
@c ==================================================================
-@node Introduction, Installing tinc - preparations, Top, Top
+@node Introduction, Preparations, Top, Top
@chapter Introduction
@cindex tinc
Because the tunnel appears to the IP level network code as a normal
network device, there is no need to adapt any existing software.
-
-This tunneling allows VPN sites to share information with each other
+The encrypted tunnels allows VPN sites to share information with each other
over the Internet without exposing any information to others.
-This document is the manual for tinc. Included are chapters on how to
+This document is the manual for tinc. Included are chapters on how to
configure your computer to use tinc, as well as the configuration
process of tinc itself.
@menu
* VPNs:: Virtual Private Networks in general
* tinc:: about tinc
-* Supported platforms::
+* Supported platforms::
@end menu
@c ==================================================================
@cindex VPN
A Virtual Private Network or VPN is a network that can only be accessed
-by a few elected computers that participate. This goal is achievable in
+by a few elected computers that participate. This goal is achievable in
more than just one way.
@cindex private
-Private networks can consist of a single stand-alone ethernet LAN. Or
-even two computers hooked up using a null-modem cable. In these cases,
+Private networks can consist of a single stand-alone Ethernet LAN. Or
+even two computers hooked up using a null-modem cable. In these cases,
it is
obvious that the network is @emph{private}, no one can access it from the
-outside. But if your computers are linked to the internet, the network
+outside. But if your computers are linked to the Internet, the network
is not private anymore, unless one uses firewalls to block all private
-traffic. But then, there is no way to send private data to trusted
-computers on the other end of the internet.
+traffic. But then, there is no way to send private data to trusted
+computers on the other end of the Internet.
@cindex virtual
-This problem can be solved by using @emph{virtual} networks. Virtual
-networks can live on top of other networks, but do not interfere with
-each other. Mostly, virtual networks appear like a singe LAN, even though
-they can span the entire world. But virtual networks can't be secured
+This problem can be solved by using @emph{virtual} networks. Virtual
+networks can live on top of other networks, but they use encapsulation to
+keep using their private address space so they do not interfere with
+the Internet. Mostly, virtual networks appear like a singe LAN, even though
+they can span the entire world. But virtual networks can't be secured
by using firewalls, because the traffic that flows through it has to go
-through the internet, where other people can look at it.
+through the Internet, where other people can look at it.
+
+As is the case with either type of VPN, anybody could eavesdrop. Or
+worse, alter data. Hence it's probably advisable to encrypt the data
+that flows over the network.
-When one introduces encryption, we can form a true VPN. Other people may
+When one introduces encryption, we can form a true VPN. Other people may
see encrypted traffic, but if they don't know how to decipher it (they
need to know the key for that), they cannot read the information that flows
-through the VPN. This is what tinc was made for.
-
-@cindex virtual
-tinc uses normal IP datagrams to encapsulate data that goes over the VPN
-network link. In this case it's also clear that the network is
-@emph{virtual}, because no direct network link has to exist between to
-participants.
-
-As is the case with either type of VPN, anybody could eavesdrop. Or
-worse, alter data. Hence it's probably advisable to encrypt the data
-that flows over the network.
+through the VPN. This is what tinc was made for.
@c ==================================================================
@section tinc
@cindex vpnd
-@cindex ethertap
I really don't quite remember what got us started, but it must have been
-Guus' idea. He wrote a simple implementation (about 50 lines of C) that
-used the @emph{ethertap} device that Linux knows of since somewhere
-about kernel 2.1.60. It didn't work immediately and he improved it a
-bit. At this stage, the project was still simply called @samp{vpnd}.
+Guus' idea. He wrote a simple implementation (about 50 lines of C) that
+used the ethertap device that Linux knows of since somewhere
+about kernel 2.1.60. It didn't work immediately and he improved it a
+bit. At this stage, the project was still simply called @samp{vpnd}.
Since then, a lot has changed---to say the least.
runtime-configurable---in short, it has become a full-fledged
professional package.
-A lot can---and will be---changed. I have a few things that I'd like to
-see in the future releases of tinc. Not everything will be available in
-the near future. Our first objective is to make tinc work perfectly as
+@cindex Traditional VPNs
+@cindex scalability
+tinc also allows more than two sites to connect to eachother and form a single VPN.
+Traditionally VPNs are created by making tunnels, which only have two endpoints.
+Larger VPNs with more sites are created by adding more tunnels.
+tinc takes another approach: only endpoints are specified,
+the software itself will take care of creating the tunnels.
+This allows for easier configuration and improved scalability.
+
+A lot can---and will be---changed. We have a number of things that we would like to
+see in the future releases of tinc. Not everything will be available in
+the near future. Our first objective is to make tinc work perfectly as
it stands, and then add more advanced features.
-Meanwhile, we're always open-minded towards new ideas. And we're
+Meanwhile, we're always open-minded towards new ideas. And we're
available too.
@node Supported platforms, , tinc, Introduction
@section Supported platforms
-tinc works on Linux, FreeBSD and Solaris. These are the three platforms
+@cindex platforms
+tinc has been verified to work under Linux, FreeBSD and Solaris, with
+various hardware architectures. These are the three platforms
that are supported by the universial TUN/TAP device driver, so if
support for other operating systems is added to this driver, perhaps
tinc will run on them as well. Without this driver, tinc will most
likely compile and run, but it will not be able to send or receive data
packets.
+@cindex release
+The official release only truly supports Linux.
+For an up to date list of supported platforms, please check the list on
+our website:
+@uref{http://tinc.nl.linux.org/platforms.html}.
+
+
@c ==================================================================
@subsection Linux
+@cindex Linux
tinc was first written for Linux running on an intel x86 processor, so
this is the best supported platform. The protocol however, and actually
anything about tinc, has been rewritten to support random byte ordering
and arbitrary word length. So in theory it should run on other
-processors that Linux runs on. Take care however, we haven't been able
-to really test it yet. If you want to run tinc on another platform than
-x86, and want to tell us how it went, please do so.
+processors that Linux runs on. It has already been verified to run on
+alpha and sparc processors as well.
-tinc uses the ethertap device that is provided in the standard kernel
-since version 2.1.60, so anything above that (2.2.x, 2.3.x, and the
-2.4.0-testx (which is current at the time of this writing) kernel
-versions) is able to support tinc.
+tinc uses the ethertap device or the universal TUN/TAP driver. The former is provided in the standard kernel
+from version 2.1.60 up to 2.3.x, but has been replaced in favour of the TUN/TAP driver in kernel versions 2.4.0 and later.
@c ==================================================================
@subsection FreeBSD
+@cindex FreeBSD
tinc on FreeBSD relies on the universial TUN/TAP driver for its data
-acquisition from the kernel. Therefore, tinc suports the same platforms
+acquisition from the kernel. Therefore, tinc will work on the same platforms
as this driver. These are: FreeBSD 3.x, 4.x, 5.x.
@c ==================================================================
@subsection Solaris
+@cindex Solaris
tinc on Solaris relies on the universial TUN/TAP driver for its data
-acquisition from the kernel. Therefore, tinc suports the same platforms
+acquisition from the kernel. Therefore, tinc will work on the same platforms
as this driver. These are: Solaris, 2.1.x.
@c
@c ==================================================================
-@node Installing tinc - preparations, Installing tinc - installation, Introduction, Top
-@chapter Installing tinc: preparations
+@node Preparations, Installation, Introduction, Top
+@chapter Preparations
This chapter contains information on how to prepare your system to
support tinc.
@menu
-* Configuring the kernel::
-* Libraries::
+* Configuring the kernel::
+* Libraries::
@end menu
@c ==================================================================
-@node Configuring the kernel, Libraries, Installing tinc - preparations, Installing tinc - preparations
+@node Configuring the kernel, Libraries, Preparations, Preparations
@section Configuring the kernel
-If you are running Linux, chances are good that your kernel already
-supports all the devices that tinc needs for proper operation. For
-example, the standard kernel from Redhat Linux already has support for
-ethertap and netlink compiled in. Debian users can use the modconf
-utility to select the modules. If your Linux distribution supports this
-method of selecting devices, look out for something called `ethertap',
-and `netlink_dev'. You need both these devices.
-
-If you can install these devices in a similar manner, you may skip this
-section.
+@cindex RedHat
+@cindex Debian
+@cindex netlink_dev
+@cindex tun
+@cindex ethertap
+If you are running Linux, chances are good that your kernel already supports
+all the devices that tinc needs for proper operation. For example, the
+standard kernel from Redhat Linux already has support for ethertap and netlink
+compiled in. Debian users can use the modconf utility to select the modules.
+If your Linux distribution supports this method of selecting devices, look out
+for something called `ethertap', and `netlink_dev' if it is using a kernel
+version prior to 2.4.0. In that case you will need both these devices. If you
+are using kernel 2.4.0 or later, you need to select `tun'.
+
+@cindex Kernel-HOWTO
+If you can install these devices in a similar manner, you may skip this section.
+Otherwise, you will have to recompile the kernel in order to turn on the required features.
+If you are unfamiliar with the process of configuring and compiling a new kernel,
+you should read the @uref{http://howto.linuxberg.com/LDP/HOWTO/Kernel-HOWTO.html, Kernel HOWTO} first.
@menu
-* Configuration of the Linux kernel::
-* Configuration of the FreeBSD kernel::
-* Configuration of the Solaris kernel::
+* Configuration of Linux kernels 2.1.60 up to 2.4.0::
+* Configuration of Linux kernels 2.4.0 and higher::
+* Configuration of FreeBSD kernels::
+* Configuration of Solaris kernels::
@end menu
@c ==================================================================
-@node Configuration of the Linux kernel, Configuration of the FreeBSD kernel, Configuring the kernel, Configuring the kernel
-@subsection Configuring the Linux kernel
-
-Since this particular implementation only runs on 2.1 or higher Linux
-kernels, you should grab one (2.2 is current at this time). A 2.0 port
-is not really possible, unless someone tells me someone ported the
-ethertap and netlink devices back to 2.0.
-
-If you are unfamiliar with the process of configuring and compiling a
-new kernel, you should read the
-@uref{http://howto.linuxberg.com/LDP/HOWTO/Kernel-HOWTO.html, Kernel
-HOWTO} first. Do that now!
+@node Configuration of Linux kernels 2.1.60 up to 2.4.0, Configuration of Linux kernels 2.4.0 and higher, Configuring the kernel, Configuring the kernel
+@subsection Configuration of Linux kernels 2.1.60 up to 2.4.0
-Here are the options you have to turn on when configuring a new
-kernel.
-
-For kernel 2.2.x:
+Here are the options you have to turn on when configuring a new kernel:
@example
Code maturity level options
[*] Prompt for development and/or incomplete code/drivers
Networking options
[*] Kernel/User netlink socket
-<*> Netlink device emulation
+<M> Netlink device emulation
Network device support
-<*> Ethertap network tap
+<M> Ethertap network tap
@end example
-For kernel 2.3.x and 2.4.x:
+If you want to run more than one instance of tinc or other programs that use
+the ethertap, you have to compile the ethertap driver as a module, otherwise
+you can also choose to compile it directly into the kernel.
+
+If you decide to build any of these as dynamic kernel modules, it's a good idea
+to add these lines to @file{/etc/modules.conf}:
+
+@example
+alias char-major-36 netlink_dev
+alias tap0 ethertap
+options tap0 -o tap0 unit=0
+alias tap1 ethertap
+options tap1 -o tap1 unit=1
+...
+alias tap@emph{N} ethertap
+options tap@emph{N} -o tap@emph{N} unit=@emph{N}
+@end example
+
+Add as much alias/options lines as necessary.
+
+
+@c ==================================================================
+@node Configuration of Linux kernels 2.4.0 and higher, Configuration of FreeBSD kernels, Configuration of Linux kernels 2.1.60 up to 2.4.0, Configuring the kernel
+@subsection Configuration of Linux kernels 2.4.0 and higher
+
+Here are the options you have to turn on when configuring a new kernel:
@example
Code maturity level options
[*] Prompt for development and/or incomplete code/drivers
-Networking options
-[*] Kernel/User netlink socket
-<*> Netlink device emulation
Network device support
-<*> Universal TUN/TAP device driver support
+<M> Universal TUN/TAP device driver support
@end example
+It's not necessary to compile this driver as a module, even if you are going to
+run more than one instance of tinc.
+
+If you have an early 2.4 kernel, you can choose both the TUN/TAP driver and the
+`Ethertap network tap' device. This latter is marked obsolete, and chances are
+that it won't even function correctly anymore. Make sure you select the
+universal TUN/TAP driver.
-Any other options not mentioned here are not relevant to tinc. If you
-decide to build any of these as dynamic kernel modules, it's a good idea
-to add these lines to @file{/etc/modules.conf}.
+If you decide to build the TUN/TAP driver as a kernel module, add these lines
+to @file{/etc/modules.conf}:
@example
-alias tap0 ethertap
-alias char-major-36 netlink_dev
+alias char-major-10-200 tun
@end example
-If you have a 2.4 kernel, you can also choose to use the `Ethertap
-network tap' device. This is marked obsolete, because the universal
-TUN/TAP driver is a newer implementation that is supposed to be used in
-favor of ethertap. For tinc, it doesn't really matter which one you
-choose; based on the device file name, tinc will make the right choice
-about what protocol to use.
-
-Finally, after having set up other options, build the kernel and boot
-it. Unfortunately it's not possible to insert these modules in a
-running kernel.
-
@c ==================================================================
-@node Configuration of the FreeBSD kernel, Configuration of the Solaris kernel, Configuration of the Linux kernel, Configuring the kernel
-@subsection Configuring the FreeBSD kernel
+@node Configuration of FreeBSD kernels, Configuration of Solaris kernels, Configuration of Linux kernels 2.4.0 and higher, Configuring the kernel
+@subsection Configuration of FreeBSD kernels
This section will contain information on how to configure your FreeBSD
kernel to support the universal TUN/TAP device. For 5.0 and 4.1
@c ==================================================================
-@node Configuration of the Solaris kernel, , Configuration of the FreeBSD kernel, Configuring the kernel
-@subsection Configuring the Solaris kernel
+@node Configuration of Solaris kernels, , Configuration of FreeBSD kernels, Configuring the kernel
+@subsection Configuration of Solaris kernels
This section will contain information on how to configure your Solaris
kernel to support the universal TUN/TAP device. You need to install
@c ==================================================================
-@node Libraries, , Configuring the kernel, Installing tinc - preparations
+@node Libraries, , Configuring the kernel, Preparations
@section Libraries
@cindex requirements
+@cindex libraries
Before you can configure or build tinc, you need to have the OpenSSL
library installed on your system. If you try to configure tinc without
having installed it, configure will give you an error message, and stop.
@menu
-* OpenSSL::
+* OpenSSL::
@end menu
@cindex OpenSSL
For all cryptography-related functions, tinc uses the functions provided
-by the OpenSSL library. We recommend using version 0.9.5 or 0.9.6 of
-this library. Other versions may also work, but we can guarantee
-nothing.
+by the OpenSSL library.
If this library is not installed, you wil get an error when configuring
tinc for build. Support for running tinc without having OpenSSL
make sure you build development and runtime libraries (which is the
default).
+If you installed the OpenSSL libraries from source, it may be necessary
+to let configure know where they are, by passing configure one of the
+--with-openssl-* parameters.
+
+@example
+--with-openssl=DIR OpenSSL library and headers prefix
+--with-openssl-include=DIR OpenSSL headers directory
+ (Default is OPENSSL_DIR/include)
+--with-openssl-lib=DIR OpenSSL library directory
+ (Default is OPENSSL_DIR/lib)
+@end example
+
+
+@subsubheading License
+
+@cindex license
+Since the license under which OpenSSL is distributed is not directly
+compatible with the terms of the GNU GPL
+@uref{http://www.openssl.org/support/faq.html#LEGAL2}, therefore we
+include an addition to the GPL (see also the file COPYING.README):
+
+@quotation
+This program is released under the GPL with the additional exemption
+that compiling, linking, and/or using OpenSSL is allowed. You may
+provide binary packages linked to the OpenSSL libraries, provided that
+all other requirements of the GPL are met.
+@end quotation
+
@c
@c
@c
@c ==================================================================
-@node Installing tinc - installation, Configuring tinc, Installing tinc - preparations, Top
-@chapter Installing tinc: installation
+@node Installation, Configuration, Preparations, Top
+@chapter Installation
If you use Redhat or Debian, you may want to install one of the
precompiled packages for your system. These packages are equipped with
the checksums of these files listed; you may wish to check these with
md5sum before continuing.
-tinc comes in a handy autoconf/automake package, which you can just
-treat the same as any other package. Which is just untar it, type
+tinc comes in a convenient autoconf/automake package, which you can just
+treat the same as any other package. Which is just untar it, type
`configure' and then `make'.
-
More detailed instructions are in the file @file{INSTALL}, which is
included in the source distribution.
@menu
-* Building tinc::
-* System files::
-* Interfaces::
+* Building and installing tinc::
+* System files::
@end menu
@c ==================================================================
-@node Building tinc, System files, Installing tinc - installation, Installing tinc - installation
-@section Building tinc
+@node Building and installing tinc, System files, Installation, Installation
+@section Building and installing tinc
+
+Detailed instructions on configuring the source, building tinc and installing tinc
+can be found in the file called @file{INSTALL}.
-Detailed instructions on configuring the source and building tinc can be
-found in the file called @file{INSTALL}.
+@cindex binary package
+If you happen to have a binary package for tinc for your distribution,
+you can use the package management tools of that distribution to install tinc.
+The documentation that comes along with your distribution will tell you how to do that.
@c ==================================================================
-@node System files, Interfaces, Building tinc, Installing tinc - installation
+@node System files, , Building and installing tinc, Installation
@section System files
-Before you can run tinc, you
+Before you can run tinc, you must make sure you have all the needed
+files on your system.
@menu
-* Device files::
-* Other files::
+* Device files::
+* Other files::
@end menu
@node Device files, Other files, System files, System files
@subsection Device files
+@cindex device files
First, you'll need the special device file(s) that form the interface
between the kernel and the daemon.
eavesdropping would become a bit too easy. This does, however, imply
that you'd have to run tincd as root.
-If you use the universal TUN/TAP driver, you have to create the
-following device files (unless they already exist):
+If you use Linux and have a kernel version prior to 2.4.0, you have to make the
+ethertap devices:
@example
-mknod -m 600 /dev/... c .. ..
-chown 0.0 /dev/...
+mknod -m 600 /dev/tap0 c 36 16
+chown 0.0 /dev/tap0
+mknod -m 600 /dev/tap1 c 36 17
+chown 0.0 /dev/tap0
+...
+mknod -m 600 /dev/tap@emph{N} c 36 @emph{N+16}
+chown 0.0 /dev/tap@emph{N}
@end example
-If you want to have more devices, the device numbers will be .. .. ...
-
-If you use Linux, and you run the new 2.4 kernel using the devfs
-filesystem, then the tap device will be automatically generated as
-@file{/dev/netlink/tap0}.
+There is a maximum of 16 ethertap devices.
-If you use Linux and have kernel 2.2.x, you have to make the ethertap
-devices:
+If you use the universal TUN/TAP driver, you have to create the
+following device file (unless it already exist):
@example
-mknod -m 600 /dev/tap0 c 36 16
-chown 0.0 /dev/tap0
+mknod -m 600 /dev/tun c 10 200
+chown 0.0 /dev/tun
@end example
-Any further ethertap devices have minor device number 16 through 31.
+If you use Linux, and you run the new 2.4 kernel using the devfs filesystem,
+then the TUN/TAP device will probably be automatically generated as
+@file{/dev/net/tun}.
+
+Unlike the ethertap device, you do not need multiple device files if
+you are planning to run multiple tinc daemons.
@c ==================================================================
@subsubheading @file{/etc/networks}
You may add a line to @file{/etc/networks} so that your VPN will get a
-symbolic name. For example:
+symbolic name. For example:
@example
myvpn 10.0.0.0
@end example
-This has nothing to do with the MyVPNIP configuration variable that will be
-discussed later, it is only to make the output of the route command more
-legible.
-
@subsubheading @file{/etc/services}
-You may add this line to @file{/etc/services}. The effect is that you
-may supply a @samp{tinc} as a valid port number to some programs. The
+@cindex port numbers
+You may add this line to @file{/etc/services}. The effect is that you
+may supply a @samp{tinc} as a valid port number to some programs. The
number 655 is registered with the IANA.
@example
@end example
-@c ==================================================================
-@node Interfaces, , System files, Installing tinc - installation
-@section Interfaces
-
-Before you can start transmitting data over the tinc tunnel, you must
-set up the ethertap network devices.
-
-First, decide which IP addresses you want to have associated with these
-devices, and what network mask they must have. You also need these
-numbers when you are going to configure tinc itself. @xref{Configuring
-tinc}.
-
-It doesn't matter much which part you do first, setting up the network
-devices or configure tinc. But they both have to be done before you try
-to start a tincd.
-
-The actual setup of the ethertap device is quite simple, just repeat
-after me:
-
-@example
-ifconfig tap@emph{n} hw ether fe:fd:@emph{xx}:@emph{xx}:@emph{xx}:@emph{xx}
-@end example
-
-The @emph{n} here is the number of the ethertap device you want to use.
-It should be the same @emph{n} as the one you use for
-@file{/dev/tap@emph{n}}. The @emph{xx}s are four hexadecimal numbers
-(0--ff). With previous versions of tincd, it didn't matter what they
-were. But newer kernels require properly set up ethernet addresses. In
-fact, the old behavior was wrong. It is required that the @emph{xx}s
-match the numbers of the IP address you will give to the tap device and
-to the MyOwnVPNIP configuration (which will be discussed later).
-
-@cindex MAC address
-@cindex hardware address
-@strong{Tip}: for finding out what the MAC address of the tap interface
-should be, you can use the following command:
-
-@example
-$ printf 'fe:fd:%02x:%02x:%02x:%02x' 10 1 54 1
-fe:fd:0a:01:36:01
-@end example
-
-@cindex ifconfig
-To activate the device, you have to assign an IP address to it. To set
-an IP address @emph{IP} with network mask @emph{mask}, do the following:
-
-@example
-ifconfig tap@emph{n} @emph{xx}.@emph{xx}.@emph{xx}.@emph{xx} netmask @emph{mask}
-@end example
-
-@cindex netmask
-The netmask is the mask of the @emph{entire} VPN network, not just your
-own subnet. It is the same netmask you will have to specify with the
-VpnMask configuration variable.
-
-
@c
@c
@c
@c ==================================================================
-@node Configuring tinc, Running tinc, Installing tinc - installation, Top
-@chapter Configuring tinc
+@node Configuration, Running tinc, Installation, Top
+@chapter Configuration
@menu
-* Multiple networks::
-* How connections work::
-* Configuration file::
-* Example::
+* Configuration introduction::
+* Multiple networks::
+* How connections work::
+* Configuration files::
+* Generating keypairs::
+* Network interfaces::
+* Example configuration::
@end menu
@c ==================================================================
-@node Multiple networks, How connections work, Configuring tinc, Configuring tinc
-@section Multiple networks
+@node Configuration introduction, Multiple networks, Configuration, Configuration
+@section Configuration introduction
+
+@cindex Network Administrators Guide
+Before actually starting to configure tinc and editing files,
+make sure you have read this entire section so you know what to expect.
+Then, make it clear to yourself how you want to organize your VPN:
+What are the nodes (computers running tinc)?
+What IP addresses/subnets do they have?
+What is the network mask of the entire VPN?
+Do you need special firewall rules?
+Do you have to set up masquerading or forwarding rules?
+These questions can only be answered by yourself,
+you will not find the answers in this documentation.
+Make sure you have an adequate understanding of networks in general.
+A good resource on networking is the
+@uref{http://www.linuxdoc.org/LDP/nag2/, Linux Network Administrators Guide}.
+
+If you have everything clearly pictured in your mind,
+proceed in the following order:
+First, generate the configuration files (tinc.conf, your host configuration file, tinc-up and perhaps tinc-down).
+Then generate the keypairs.
+Finally, distribute the host configuration files.
+These steps are described in the subsections below.
-@c from the manpage
-It is perfectly OK for you to run more than one tinc daemon.
-However, in its default form, you will soon notice that you can't use
-two different configuration files without the -c option.
+@c ==================================================================
+@node Multiple networks, How connections work, Configuration introduction, Configuration
+@section Multiple networks
-We have thought of another way of dealing with this: network names. This
-means that you call tincd with the -n argument, which will assign a name
-to this daemon.
+@cindex multiple networks
+@cindex netname
+In order to allow you to run more than one tinc daemon on one computer,
+for instance if your computer is part of more than one VPN,
+you can assign a ``netname'' to your VPN.
+It is not required if you only run one tinc daemon,
+it doesn't even have to be the same on all the sites of your VPN,
+but it is recommended that you choose one anyway.
+
+We will asume you use a netname throughout this document.
+This means that you call tincd with the -n argument,
+which will assign a netname to this daemon.
The effect of this is that the daemon will set its configuration
-``root'' to /etc/tinc/nn/, where nn is your argument to the -n
-option. You'll notice that it appears in syslog as ``tinc.nn''.
+``root'' to /etc/tinc/netname/, where netname is your argument to the -n
+option. You'll notice that it appears in syslog as ``tinc.netname''.
However, it is not strictly necessary that you call tinc with the -n
-option. In this case, the network name would just be empty, and it will
-be used as such. tinc now looks for files in /etc/tinc/, instead of
-/etc/tinc/nn/; the configuration file should be /etc/tinc/tinc.conf,
-and the passphrases are now expected to be in /etc/tinc/passphrases/.
+option. In this case, the network name would just be empty, and it will
+be used as such. tinc now looks for files in /etc/tinc/, instead of
+/etc/tinc/netname/; the configuration file should be /etc/tinc/tinc.conf,
+and the host configuration files are now expected to be in /etc/tinc/hosts/.
But it is highly recommended that you use this feature of tinc, because
-it will be so much clearer whom your daemon talks to. Hence, we will
+it will be so much clearer whom your daemon talks to. Hence, we will
assume that you use it.
@c ==================================================================
-@node How connections work, Configuration file, Multiple networks, Configuring tinc
+@node How connections work, Configuration files, Multiple networks, Configuration
@section How connections work
-Before going on, first a bit on how tinc sees connections.
-
-When tinc starts up, it reads in the configuration file and parses the
-command-line options. If it sees a `ConnectTo' value in the file, it
-will try to connect to it, on the given port. If this fails, tinc exits.
+When tinc starts up, it parses the command-line options and then
+reads in the configuration file.
+If it sees a `ConnectTo' value pointing to another tinc daemon in the file,
+it will try to connect to that other one.
+Whether this succeeds or not and whether `ConnectTo' is specified or not,
+tinc will listen for incoming connection from other deamons.
+If you did specify a `ConnectTo' value and the other side is not responding,
+tinc will keep retrying.
+This means that once started, tinc will stay running until you tell it to stop,
+and failures to connect to other tinc daemons will not stop your tinc daemon
+for trying again later.
+This means you don't have to intervene if there are any network problems.
+
+@cindex client
+@cindex server
+There is no real distinction between a server and a client in tinc.
+If you wish, you can view a tinc daemon without a `ConnectTo' value as a server,
+and one which does specify such a value as a client.
+It does not matter if two tinc daemons have a `ConnectTo' value pointing to eachother however.
@c ==================================================================
-@node Configuration file, Example, How connections work, Configuring tinc
-@section Configuration file
+@node Configuration files, Generating keypairs, How connections work, Configuration
+@section Configuration files
The actual configuration of the daemon is done in the file
-@file{/etc/tinc/nn/tinc.conf}.
+@file{/etc/tinc/netname/tinc.conf} and at least one other file in the directory
+@file{/etc/tinc/netname/hosts/}.
-This file consists of comments (lines started with a #) or assignments
+These file consists of comments (lines started with a #) or assignments
in the form of
@example
@end example
The variable names are case insensitive, and any spaces, tabs, newlines
-and carriage returns are ignored. Note: it is not required that you put
+and carriage returns are ignored. Note: it is not required that you put
in the `=' sign, but doing so improves readability. If you leave it
out, remember to replace it with at least one space character.
+In this section all valid variables are listed in alphabetical order.
+The default value is given between parentheses,
+other comments are between square brackets and
+required directives are given in @strong{bold}.
+
@menu
-* Variables::
+* Main configuration variables::
+* Host configuration variables::
+* How to configure::
@end menu
-@c ==================================================================
-@node Variables, , Configuration file, Configuration file
-@subsection Variables
-Here are all valid variables, listed in alphabetical order. The default
-value, required or optional is given between parentheses.
+@c ==================================================================
+@node Main configuration variables, Host configuration variables, Configuration files, Configuration files
+@subsection Main configuration variables
-@c straight from the manpage
@table @asis
-@item ConnectPort = <port> (655)
-Connect to the upstream host (given with the ConnectTo directive) on
-port port. port may be given in decimal (default), octal (when preceded
-by a single zero) or hexadecimal (prefixed with 0x). port is the port
-number for both the UDP and the TCP (meta) connections.
-
-@item ConnectTo = <IP address|hostname> (optional)
-Specifies which host to connect to on startup. Multiple ConnectTo variables
-may be specified, if connecting to the first one fails then tinc will try
-the next one, and so on. It is possible to specify hostnames for dynamic IP
-addresses (like those given on dyndns.org), tinc will not cache the resolved
-IP address.
+@item @strong{ConnectTo = <name>}
+@cindex ConnectTo
+Specifies which host to connect to on startup. Multiple ConnectTo
+variables may be specified, if connecting to the first one fails then
+tinc will try the next one, and so on. It is possible to specify
+hostnames for dynamic IP addresses (like those given on dyndns.org),
+tinc will not cache the resolved IP address.
If you don't specify a host with ConnectTo, regardless of whether a
value for ConnectPort is given, tinc won't connect at all, and will
instead just listen for incoming connections.
@item Hostnames = <yes|no> (no)
-This option selects whether IP addresses (both real and on the VPN) should
-be resolved. Since DNS lookups are blocking, it might affect tinc's
-efficiency, even stopping the daemon for a few seconds everytime it does
-a lookup if your DNS server is not responding.
-
-This does not affect resolving hostnames to IP addresses from the configuration
-file.
-
-@item IndirectData = <yes|no> (no)
-This option specifies whether other tinc daemons besides the one you
-specified with ConnectTo can make a direct connection to you. This is
-especially useful if you are behind a firewall and it is impossible
-to make a connection from the outside to your tinc daemon. Otherwise,
-it is best to leave this option out or set it to no.
-
-@item Interface = <device> (optional)
-If you have more than one network interface in your computer, tinc will by
-default listen on all of them for incoming connections. It is possible to
-bind tinc to a single interface like eth0 or ppp0 with this variable.
-
-@item InterfaceIP = <local address> (optional)
-If your computer has more than one IP address on a single interface (for example
-if you are running virtual hosts), tinc will by default listen on all of them for
-incoming connections. It is possible to bind tinc to a single IP address with
-this variable. It is still possible to listen on several interfaces at the same
-time though, if they share the same IP address.
+@cindex Hostnames
+This option selects whether IP addresses (both real and on the VPN)
+should be resolved. Since DNS lookups are blocking, it might affect
+tinc's efficiency, even stopping the daemon for a few seconds everytime
+it does a lookup if your DNS server is not responding.
+
+This does not affect resolving hostnames to IP addresses from the
+configuration file.
+
+@item Interface = <device>
+@cindex Interface
+If you have more than one network interface in your computer, tinc will
+by default listen on all of them for incoming connections. It is
+possible to bind tinc to a single interface like eth0 or ppp0 with this
+variable.
+
+@item InterfaceIP = <local address>
+@cindex InterfaceIP
+If your computer has more than one IP address on a single interface (for
+example if you are running virtual hosts), tinc will by default listen
+on all of them for incoming connections. It is possible to bind tinc to
+a single IP address with this variable. It is still possible to listen
+on several interfaces at the same time though, if they share the same IP
+address.
@item KeyExpire = <seconds> (3600)
+@cindex KeyExpire
This option controls the time the encryption keys used to encrypt the data
-are valid. It is common practice to change keys at regular intervals to
+are valid. It is common practice to change keys at regular intervals to
make it even harder for crackers, even though it is thought to be nearly
impossible to crack a single key.
-@item ListenPort = <port> (655)
-Listen on local port port. The computer connecting to this daemon should
-use this number as the argument for his ConnectPort.
+@item @strong{Name = <name>}
+@cindex Name
+This is a symbolic name for this connection. It can be anything
-@item MyOwnVPNIP = <local address[/maskbits]> (required)
-The local address is the number that the daemon will propagate to
-other daemons on the network when it is identifying itself. Hence this
-will be the file name of the passphrase file that the other end expects
-to find the passphrase in.
+@item PingTimeout = <seconds> (60)
+@cindex PingTimeout
+The number of seconds of inactivity that tinc will wait before sending a
+probe to the other end. If that other end doesn't answer within that
+same amount of seconds, the connection is terminated, and the others
+will be notified of this.
-The local address is the IP address of the tap device, not the real IP
-address of the host running tincd. Due to changes in recent kernels, it
-is also necessary that you make the ethernet (also known as MAC) address
-equal to the IP address (see the example).
+@item PrivateKey = <key> [obsolete]
+@cindex PrivateKey
+This is the RSA private key for tinc. However, for safety reasons it is
+advised to store private keys of any kind in separate files. This prevents
+accidental eavesdropping if you are editting the configuration file.
+
+@item @strong{PrivateKeyFile = <path>} [recommended]
+@cindex PrivateKeyFile
+This is the full path name of the RSA private key file that was
+generated by ``tincd --generate-keys''. It must be a full path, not a
+relative directory.
+
+@item @strong{TapDevice = <device>} (/dev/tap0 or /dev/net/tun)
+@cindex TapDevice
+The ethertap device to use. Note that you can only use one device per
+daemon. The info pages of the tinc package contain more information
+about configuring an ethertap device for Linux.
-maskbits is the number of bits set to 1 in the netmask part.
+@end table
-@item MyVirtualIP = <local address[/maskbits]>
-This is an alias for MyOwnVPNIP.
-@item Passphrases = <directory> (/etc/tinc/NETNAME/passphrases)
-The directory where tinc will look for passphrases when someone tries to
-connect. Please see the manpage for genauth(8) for more information
-about passphrases as used by tinc.
+@c ==================================================================
+@node Host configuration variables, How to configure, Main configuration variables, Configuration files
+@subsection Host configuration variables
-@item PingTimeout = <seconds> (5)
-The number of seconds of inactivity that tinc will wait before sending a
-probe to the other end. If that other end doesn't answer within that
-same amount of seconds, the connection is terminated, and the others
-will be notified of this.
+@table @asis
+@item @strong{Address = <IP address|hostname>} [recommended]
+@cindex Address
+This variable is only required if you want to connect to this host. It
+must resolve to the external IP address where the host can be reached,
+not the one that is internal to the VPN.
+
+@item IndirectData = <yes|no> (no) [experimental]
+@cindex IndirectData
+This option specifies whether other tinc daemons besides the one you
+specified with ConnectTo can make a direct connection to you. This is
+especially useful if you are behind a firewall and it is impossible to
+make a connection from the outside to your tinc daemon. Otherwise, it
+is best to leave this option out or set it to no.
-@item TapDevice = <device> (/dev/tap0)
-The ethertap device to use. Note that you can only use one device per
-daemon. The info pages of the tinc package contain more information
-about configuring an ethertap device for Linux.
+@item Port = <port> (655)
+@cindex Port
+Connect to the upstream host (given with the ConnectTo directive) on
+port port. port may be given in decimal (default), octal (when preceded
+by a single zero) o hexadecimal (prefixed with 0x). port is the port
+number for both the UDP and the TCP (meta) connections.
-@item TCPonly = <yes|no> (no, experimental)
-If this variable is set to yes, then the packets are tunnelled over a TCP
-connection instead of a UDP connection. This is especially useful for those
-who want to run a tinc daemon from behind a masquerading firewall, or if
-UDP packet routing is disabled somehow. This is experimental code,
-try this at your own risk.
-
-@item VpnMask = <mask> (optional)
-The mask that defines the scope of the entire VPN. This option is not used
-by the tinc daemon itself, but can be used by startup scripts to configure
-the ethertap devices correctly.
+@item PublicKey = <key> [obsolete]
+@cindex PublicKey
+This is the RSA public key for this host.
+
+@item PublicKeyFile = <path> [obsolete]
+@cindex PublicKeyFile
+This is the full path name of the RSA public key file that was generated
+by ``tincd --generate-keys''. It must be a full path, not a relative
+directory.
+
+@cindex PEM format
+From version 1.0pre4 on tinc will store the public key directly into the
+host configuration file in PEM format, the above two options then are not
+necessary. Either the PEM format is used, or exactly
+@strong{one of the above two options} must be specified
+in each host configuration file, if you want to be able to establish a
+connection with that host.
+
+@item Subnet = <IP address/maskbits>
+@cindex Subnet
+This is the subnet range of all IP addresses that will be accepted by
+the host that defines it.
+
+The range must be contained in the IP address range of the tap device,
+not the real IP address of the host running tincd.
+
+@cindex CIDR notation
+maskbits is the number of bits set to 1 in the netmask part; for
+example: netmask 255.255.255.0 would become /24, 255.255.252.0 becomes
+/22. This conforms to standard CIDR notation as described in
+@uref{ftp://ftp.isi.edu/in-notes/rfc1519.txt, RFC1519}
+
+@item TCPonly = <yes|no> (no) [experimental]
+@cindex TCPonly
+If this variable is set to yes, then the packets are tunnelled over a
+TCP connection instead of a UDP connection. This is especially useful
+for those who want to run a tinc daemon from behind a masquerading
+firewall, or if UDP packet routing is disabled somehow. This is
+experimental code, try this at your own risk. It may not work at all.
+Setting this options also implicitly sets IndirectData.
@end table
+@c ==================================================================
+@node How to configure, , Host configuration variables, Configuration files
+@subsection How to configure
+
+@subsubheading Step 1. Creating the main configuration file
+
+The main configuration file will be called @file{/etc/tinc/netname/tinc.conf}.
+Adapt the following example to create a basic configuration file:
+
+@example
+Name = @emph{yourname}
+TapDevice = @emph{/dev/tap0}
+PrivateKeyFile = /etc/tinc/@emph{netname}/rsa_key.priv
+@end example
+
+Then, if you know to which other tinc daemon(s) yours is going to connect,
+add `ConnectTo' values.
+
+@subsubheading Step 2. Creating your host configuration file
+
+If you added a line containing `Name = yourname' in the main configuarion file,
+you will need to create a host configuration file @file{/etc/tinc/netname/hosts/yourname}.
+Adapt the following example to create a host configuration file:
+
+@example
+Address = @emph{your.real.hostname.org}
+Subnet = @emph{192.168.1.0/24}
+@end example
+
+You can also use an IP address instead of a hostname.
+The `Subnet' specifies the address range that is local for @emph{your part of the VPN only}.
+If you have multiple address ranges you can specify more than one `Subnet'.
+You might also need to add a `Port' if you want your tinc daemon to run on a different port number than the default (655).
+
+
+@c ==================================================================
+@node Generating keypairs, Network interfaces, Configuration files, Configuration
+@section Generating keypairs
+
+@cindex key generation
+Now that you have already created the main configuration file and your host configuration file,
+you can easily create a public/private keypair by entering the following command:
+
+@example
+tincd -n @emph{netname} -K
+@end example
+
+tinc will generate a public and a private key and ask you where to put them.
+Just press enter to accept the defaults.
+
+
+@c ==================================================================
+@node Network interfaces, Example configuration, Generating keypairs, Configuration
+@section Network interfaces
+
+Before tinc can start transmitting data over the tunnel, it must
+set up the ethertap network devices.
+
+First, decide which IP addresses you want to have associated with these
+devices, and what network mask they must have.
+
+tinc will open an ethertap device or TUN/TAP device, which will also
+create a network interface called `tap0', or `tap1', and so on if you are using
+the ethertap driver, or a network interface with the same name as netname
+if you are using the universal TUN/TAP driver.
+
+@cindex tinc-up
+You can configure that device by putting ordinary ifconfig, route, and other commands
+to a script named @file{/etc/tinc/netname/tinc-up}. When tinc starts, this script
+will be executed. When tinc exits, it will execute the script named
+@file{/etc/tinc/netname/tinc-down}, but normally you don't need to create that script.
+
+An example @file{tinc-up} script when using the TUN/TAP driver:
+
+@example
+#!/bin/sh
+ifconfig $NETNAME hw ether fe:fd:00:00:00:00
+ifconfig $NETNAME @emph{xx}.@emph{xx}.@emph{xx}.@emph{xx} netmask @emph{mask}
+ifconfig $NETNAME -arp
+@end example
+
+@cindex MAC address
+@cindex hardware address
+The first line sets up the MAC address of the network interface.
+Due to the nature of how Ethernet and tinc work, it has to be set to fe:fd:00:00:00:00.
+(tinc versions prior to 1.0pre3 required that the MAC address matched the IP address.)
+You can use the environment variable $NETNAME to get the name of the interface.
+If you are using the ethertap driver however, you need to replace it with tap@emph{N},
+corresponding to the device file name.
+
+@cindex ifconfig
+The next line gives the interface an IP address and a netmask.
+The kernel will also automatically add a route to this interface, so normally you don't need
+to add route commands to the @file{tinc-up} script.
+The kernel will also bring the interface up after this command.
+@cindex netmask
+The netmask is the mask of the @emph{entire} VPN network, not just your
+own subnet.
+
+@cindex arp
+The last line tells the kernel not to use ARP on that interface.
+Again this has to do with how Ethernet and tinc work. Don't forget to add this line.
+
@c ==================================================================
-@node Example, , Configuration file, Configuring tinc
-@section Example
+@node Example configuration, , Network interfaces, Configuration
+@section Example configuration
-Imagine the following situation. An A-based company wants to connect
-three branch offices in B, C and D using the internet. All four offices
-have a 24/7 connection to the internet.
+@cindex example
+Imagine the following situation. Branch A of our example `company' wants to connect
+three branch offices in B, C and D using the Internet. All four offices
+have a 24/7 connection to the Internet.
-A is going to serve as the center of the network. B and C will connect
-to A, and D will connect to C. Each office will be assigned their own IP
+A is going to serve as the center of the network. B and C will connect
+to A, and D will connect to C. Each office will be assigned their own IP
network, 10.x.0.0.
@example
@end example
``gateway'' is the VPN IP address of the machine that is running the
-tincd. ``internet IP'' is the IP address of the firewall, which does not
+tincd. ``internet IP'' is the IP address of the firewall, which does not
need to run tincd, but it must do a port forwarding of TCP&UDP on port
655 (unless otherwise configured).
In this example, it is assumed that eth0 is the interface that points to
-the inner LAN of the office, although this could also be the same as the
-interface that leads to the internet. The configuration of the real
-interface is also shown as a comment, to give you an idea of how these
-example host is set up.
+the inner (physical) LAN of the office, although this could also be the
+same as the interface that leads to the Internet. The configuration of
+the real interface is also shown as a comment, to give you an idea of
+how these example host is set up. All branches use the netname `company'
+for this particular VPN.
+
+@subsubheading For Branch A
-@subsubheading For A
+@emph{BranchA} would be configured like this:
-@emph{A} would be configured like this:
+In @file{/etc/tinc/company/tinc-up}:
@example
-#ifconfig eth0 10.1.54.1 netmask 255.255.0.0 broadcast 10.1.255.255
-ifconfig tap0 hw ether fe:fd:0a:01:36:01
+# Real interface of internal network:
+# ifconfig eth0 10.1.54.1 netmask 255.255.0.0 broadcast 10.1.255.255
+
+ifconfig tap0 hw ether fe:fd:00:00:00:00
ifconfig tap0 10.1.54.1 netmask 255.0.0.0
+ifconfig tap0 -arp
@end example
-and in /etc/tinc/tinc.conf:
+and in @file{/etc/tinc/company/tinc.conf}:
@example
+Name = BranchA
+PrivateKey = /etc/tinc/company/rsa_key.priv
TapDevice = /dev/tap0
-MyVirtualIP = 10.1.54.1/16
-VpnMask = 255.0.0.0
@end example
-@subsubheading For B
+On all hosts, /etc/tinc/company/hosts/BranchA contains:
@example
-#ifconfig eth0 10.2.43.8 netmask 255.255.0.0 broadcast 10.2.255.255
-ifconfig tap0 hw ether fe:fd:0a:02:01:0c
+Subnet = 10.1.0.0/16
+Address = 1.2.3.4
+
+Note that the IP addresses of eth0 and tap0 are the same.
+This is quite possible, if you make sure that the netmasks of the interfaces are different.
+It is in fact recommended to give give both real internal network interfaces and tap interfaces the same IP address,
+since that will make things a lot easier to remember and set up.
+
+-----BEGIN RSA PUBLIC KEY-----
+...
+-----END RSA PUBLIC KEY-----
+@end example
+
+
+@subsubheading For Branch B
+
+In @file{/etc/tinc/company/tinc-up}:
+
+@example
+# Real interface of internal network:
+# ifconfig eth0 10.2.43.8 netmask 255.255.0.0 broadcast 10.2.255.255
+
+ifconfig tap0 hw ether fe:fd:00:00:00:00
ifconfig tap0 10.2.1.12 netmask 255.0.0.0
+ifconfig tap0 -arp
@end example
-and in /etc/tinc/tinc.conf:
+and in @file{/etc/tinc/company/tinc.conf}:
@example
-TapDevice = /dev/tap0
-MyVirtualIP = 10.2.1.12/16
-ConnectTo = 1.2.3.4
-VpnMask = 255.0.0.0
+Name = BranchB
+ConnectTo = BranchA
+PrivateKey = /etc/tinc/company/rsa_key.priv
@end example
Note here that the internal address (on eth0) doesn't have to be the
-same as on the tap0 device. Also, ConnectTo is given so that no-one can
+same as on the tap0 device. Also, ConnectTo is given so that no-one can
connect to this node.
-@subsubheading For C
+On all hosts, in @file{/etc/tinc/company/hosts/BranchB}:
@example
-#ifconfig eth0 10.3.69.254 netmask 255.255.0.0 broadcast 10.3.255.255
-ifconfig tap0 hw ether fe:fd:0a:03:45:fe
-ifconfig tap0 10.3.69.254 netmask 255.0.0.0
-@end example
-
-and in /etc/tinc/A/tinc.conf:
+Subnet = 10.2.0.0/16
+Address = 2.3.4.5
-@example
-MyVirtualIP = 10.3.69.254/16
-TapDevice = /dev/tap1
-ConnectTo = 1.2.3.4
-ListenPort = 2000
-VpnMask = 255.0.0.0
+-----BEGIN RSA PUBLIC KEY-----
+...
+-----END RSA PUBLIC KEY-----
@end example
-C already has another daemon that runs on port 655, so they have to
-reserve another port for tinc. It can connect to other tinc daemons on
-the regular port though, so no ConnectPort variable is needed.
-They also use the netname to distinguish
-between the two. tinc is started with `tincd -n A'.
-@subsubheading For D
+@subsubheading For Branch C
+
+In @file{/etc/tinc/company/tinc-up}:
@example
-#ifconfig tap0 10.4.3.32 netmask 255.255.0.0 broadcast 10.4.255.255
-ifconfig tap0 hw ether fe:fd:0a:04:03:20
-ifconfig tap0 10.4.3.32 netmask 255.0.0.0
+# Real interface of internal network:
+# ifconfig eth0 10.3.69.254 netmask 255.255.0.0 broadcast 10.3.255.255
+
+ifconfig tap1 hw ether fe:fd:00:00:00:00
+ifconfig tap1 10.3.69.254 netmask 255.0.0.0
+ifconfig tap1 -arp
@end example
-and in /etc/tinc/tinc.conf:
+and in @file{/etc/tinc/company/tinc.conf}:
@example
-MyVirtualIP = 10.4.3.32/16
-ConnectTo = 3.4.5.6
-ConnectPort = 2000
-VpnMask=255.0.0.0
+Name = BranchC
+ConnectTo = BranchA
+TapDevice = /dev/tap1
@end example
-D will be connecting to C, which has a tincd running for this network on
-port 2000. Hence they need to put in a ConnectPort, but it doesn't need
-to have a different ListenPort.
+C already has another daemon that runs on port 655, so they have to
+reserve another port for tinc. It knows the portnumber it has to listen on
+from it's own host configuration file.
-@subsubheading Authentication
+On all hosts, in @file{/etc/tinc/company/hosts/BranchC}:
-A, B, C and D all generate a passphrase with genauth 2048, the output is
-stored in /etc/tinc/passphrases/local, except for C, where it should be
-/etc/tinc/A/passphrases/local.
+@example
+Address = 3.4.5.6
+Subnet = 10.3.0.0/16
+Port = 2000
-A stores a copy of B's passphrase in /etc/tinc/passphrases/10.2.1.12
+-----BEGIN RSA PUBLIC KEY-----
+...
+-----END RSA PUBLIC KEY-----
+@end example
-A stores a copy of C's passphrase in /etc/tinc/passphrases/10.3.69.254
-B stores a copy of A's passphrase in /etc/tinc/passphrases/10.1.54.1
+@subsubheading For Branch D
-C stores a copy of A's passphrase in /etc/tinc/A/passphrases/10.1.54.1
+In @file{/etc/tinc/company/tinc-up}:
-C stores a copy of D's passphrase in /etc/tinc/A/passphrases/10.4.3.32
+@example
+# Real interface of internal network:
+# ifconfig eth0 10.4.3.32 netmask 255.255.0.0 broadcast 10.4.255.255
-D stores a copy of C's passphrase in /etc/tinc/passphrases/10.3.69.254
+ifconfig company hw ether fe:fd:0a:04:03:20
+ifconfig company 10.4.3.32 netmask 255.0.0.0
+ifconfig company -arp
+@end example
-@subsubheading Starting
+and in @file{/etc/tinc/company/tinc.conf}:
-A has to start their tincd first. Then come B and C, where C has to
-provide the option `-n A', because they have more than one tinc
-network. Finally, D's tincd is started.
+@example
+Name = BranchD
+ConnectTo = BranchC
+TapDevice = /dev/net/tun
+PrivateKeyFile = /etc/tinc/company/rsa_key.priv
+@end example
+D will be connecting to C, which has a tincd running for this network on
+port 2000. It knows the port number from the host configuration file.
+Also note that since D uses the TUN/TAP driver, the network interface
+will not be called `tun' or `tap0' or something like that, but will
+have the same name as netname.
+On all hosts, in @file{/etc/tinc/company/hosts/BranchD}:
-@c ==================================================================
-@node Running tinc, Technical information, Configuring tinc, Top
-@chapter Running tinc
+@example
+Subnet = 10.4.0.0/16
+Address = 4.5.6.7
-Running tinc isn't just as easy as typing `tincd' and hoping everything
-will just work out the way you wanted. Instead, the use of tinc is a
-project that involves trust relations and more than one computer.
+-----BEGIN RSA PUBLIC KEY-----
+...
+-----END RSA PUBLIC KEY-----
+@end example
-@menu
-* Managing keys::
-* Runtime options::
-@end menu
+@subsubheading Key files
+A, B, C and D all have generated a public/private keypair with the following command:
-@c ==================================================================
-@node Managing keys, Runtime options, Running tinc, Running tinc
-@section Managing keys
+@example
+tincd -n company -K
+@end example
-Before attempting to start tinc, you have to create passphrases. When
-tinc tries to make a connection, it exchanges some sensitive
-data. Before doing so, it likes to know if the other end is
-trustworthy.
+The private key is stored in @file{/etc/tinc/company/rsa_key.priv},
+the public key is put into the host configuration file in the @file{/etc/tinc/company/hosts/} directory.
+During key generation, tinc automatically guesses the right filenames based on the -n option and
+the Name directive in the @file{tinc.conf} file (if it is available).
-To do this, both ends must have some knowledge about the other. In the
-case of tinc this is the authentication passphrase.
+@subsubheading Starting
+
+After each branch has finished configuration and they have distributed
+the host configuration files amongst them, they can start their tinc daemons.
+They don't necessarily have to wait for the other branches to have started
+their daemons, tinc will try connecting until they are available.
-This passphrase is a number, which is chosen at random. This number is
-then sent to the other computers which want to talk to us directly. To
-avoid breaking security, this should be done over a known secure channel
-(such as ssh or similar).
-All passphrases are stored in the passphrases directory, which is
-normally /etc/tinc/nn/passphrases/, but it may be changed using the
-`Passphrases' option in the config file.
+@c ==================================================================
+@node Running tinc, Technical information, Configuration, Top
+@chapter Running tinc
-To generate a passphrase, run `genauth'. genauth takes one argument,
-which is the length of the passphrase in bits. The length of the
-passphrase should be in the range 1024--2048 for a key length of 128
-bits. genauth creates a random number of the specified length, and puts
-it to stdout.
+If everything else is done, you can start tinc by typing the following command:
-Every computer that wants to participate in the VPN should do this, and
-store the output in the passphrases directory, in the file @file{local}.
+@example
+tincd -n @emph{netname}
+@end example
-When every computer has his own local key, it should copy it to the
-computer that it wants to talk to directly. (i.e. the one it connects to
-during startup.) This should be done via a secure channel, because it is
-sensitive information. If this is not done securely, someone might break
-in on you later on.
+@cindex daemon
+tinc will detach from the terminal and continue to run in the background like a good daemon.
+If there are any problems however you can try to increase the debug level
+and look in the syslog to find out what the problems are.
-Those non-local passphrase files must have the name of the VPN IP
-address that they will advertise to you. For instance, if a computer
-tells us it likes to be 10.1.1.3 with netmask 255.255.0.0, the file
-should still be called 10.1.1.3, and not 10.1.0.0.
+@menu
+* Runtime options::
+* Error messages::
+@end menu
@c ==================================================================
-@node Runtime options, , Managing keys, Running tinc
+@node Runtime options, Error messages, , Running tinc
@section Runtime options
Besides the settings in the configuration file, tinc also accepts some
command line options.
-This list is a longer version of that in the manpage. The latter is
+This list is a longer version of that in the manpage. The latter is
generated automatically, so may be more up-to-date.
+@cindex command line
+@cindex runtime options
+@cindex options
@c from the manpage
-@table @asis
-@item -c, --config=FILE
-Read configuration options from FILE. The default is
-@file{/etc/tinc/nn/tinc.conf}.
+@table @samp
+@item -c, --config=PATH
+Read configuration options from the directory PATH. The default is
+@file{/etc/tinc/netname/}.
+@cindex debug level
@item -d
-Increase debug level. The higher it gets, the more gets
-logged. Everything goes via syslog.
+Increase debug level. The higher it gets, the more gets
+logged. Everything goes via syslog.
0 is the default, only some basic information connection attempts get
-logged. Setting it to 1 will log a bit more, still not very
-disturbing. With two -d's tincd will log protocol information, which can
-get pretty noisy. Three or more -d's will output every single packet
+logged. Setting it to 1 will log a bit more, still not very
+disturbing. With two -d's tincd will log protocol information, which can
+get pretty noisy. Three or more -d's will output every single packet
that goes out or comes in, which probably generates more data than the
packets themselves.
@item -k, --kill
-Attempt to kill a running tincd and exit. A TERM signal (15) gets sent
-to the daemon that his its PID in /var/run/tinc.nn.pid.
+Attempt to kill a running tincd and exit. A TERM signal (15) gets sent
+to the daemon that his its PID in /var/run/tinc.pid.
-Because it kills only one tincd, you should use -n here if you use it
-normally.
+Because it kills only one tinc daemon, you should use -n here if you
+started it that way. It will then read the PID from
+@file{/var/run/tinc.NETNAME.pid}.
@item -n, --net=NETNAME
-Connect to net NETNAME. @xref{Multiple networks}.
+Connect to net NETNAME. @xref{Multiple networks}.
-@item -t, --timeout=TIMEOUT
-Seconds to wait before giving a timeout. Should not be set too low,
-because every time tincd senses a timeout, it disconnects and reconnects
-again, which will cause unnecessary network traffic and log messages.
+@item -K, --generate-keys[=BITS]
+Generate public/private keypair of BITS length. If BITS is not specified,
+1024 is the default. tinc will ask where you want to store the files,
+but will default to the configuration directory (you can use the -c or -n option
+in combination with -K). After that, tinc will quit.
@item --help
Display a short reminder of these runtime options and terminate.
@end table
+@c ==================================================================
+@node Error messages, , Runtime options, Running tinc
+@section Error messages
+
+What follows is a list of the most common error messages you can see
+when configuring tinc. Most of these messages are visible in the syslog
+only, so keep an eye on it!
+
+@table @strong
+@item Could not open /dev/tap0: No such device
+
+@itemize
+@item You forgot to `modprobe netlink_dev' or `modprobe ethertap'.
+@item You forgot to compile `Netlink device emulation' in the kernel.
+@end itemize
+
+@item Can't write to /dev/net/tun: No such device
+
+@itemize
+@item You forgot to `modprobe tun'.
+@item You forgot to compile `Universal TUN/TAP driver' in the kernel.
+@end itemize
+
+@item Packet with destination 1.2.3.4 is looping back to us!
+
+@itemize
+@item Something is not configured right. Packets are being sent out to the
+tap device, but according to the Subnet directives in your host configuration
+file, those packets should go to your own host. Most common mistake is that
+you have a Subnet line in your host configuration file with a netmask which is
+just as large as the netmask of the tap device. The latter should in almost all
+cases be larger. Rethink your configuration.
+Note that you will only see this message if you specified a debug
+level of 5 or higher!
+@item Chances are that a `Subnet = ...' line in the host configuration file of this tinc daemon is wrong.
+Change it to a subnet that is accepted locally by another interface,
+or if that is not the case, try changing the prefix length into /32.
+@end itemize
+
+@item Network doesn't work, syslog shows only packets of length 46
+
+@cindex arp
+@example
+Jan 1 12:00:00 host tinc.net[1234]: Read packet of length 46 from tap device
+Jan 1 12:00:00 host tinc.net[1234]: Trying to look up 0.0.192.168 in connection list failed!
+@end example
+@itemize
+@item Add the `ifconfig $NETNAME -arp' to tinc-up.
+@end itemize
+
+@item Network address and subnet mask do not match!
+
+@itemize
+@item The Subnet field must contain a @emph{network} address.
+@item If you only want to use one IP address, set the netmask to /32.
+@end itemize
+
+@item This is a bug: net.c:253: 24: Some error
+
+@itemize
+@item This is something that should not have happened.
+Please report this, and tell us exactly what went wrong before you got
+this message. In normal operation, these errors should not occur.
+@end itemize
+
+@item Error reading RSA key file `rsa_key.priv': No such file or directory
+
+@itemize
+@item You must specify the complete pathname.
+Specifying a relative path does not make sense here. tinc changes its
+directory to / when starting (to avoid keeping a mount point busy); and
+even if we built in a default directory to look for these files, the key
+files are bound to be in a different directory.
+@end itemize
+
+@end table
+
@c ==================================================================
@node Technical information, About us, Running tinc, Top
@chapter Technical information
-@c ==================================================================
@menu
-* The Connection::
-* Security::
+* The Connection::
+* Security::
@end menu
+
+@c ==================================================================
@node The Connection, Security, Technical information, Technical information
@section The basic philosophy of the way tinc works
-@cindex Connection
+@cindex connection
tinc is a daemon that takes VPN data and transmit that to another host
computer over the existing Internet infrastructure.
@menu
-* Protocol Preview::
-* The Meta-connection::
+* Protocol Preview::
+* The Meta-connection::
@end menu
@cindex ethertap
@cindex frame type
The data itself is read from a character device file, the so-called
-@emph{ethertap} device. This device is associated with a network
-interface. Any data sent to this interface can be read from the device,
-and any data written to the device gets sent from the interface. Data to
-and from the device is formatted as if it were a normal ethernet card,
+@emph{ethertap} device. This device is associated with a network
+interface. Any data sent to this interface can be read from the device,
+and any data written to the device gets sent from the interface. Data to
+and from the device is formatted as if it were a normal Ethernet card,
so a frame is preceded by two MAC addresses and a @emph{frame type}
field.
-So when tinc reads an ethernet frame from the device, it determines its
-type. Right now, tinc can only handle Internet Protocol version 4 (IPv4)
-frames. Plans to support other protocols are being made. When tinc knows
+So when tinc reads an Ethernet frame from the device, it determines its
+type. Right now, tinc can only handle Internet Protocol version 4 (IPv4)
+frames, because it needs IP headers for routing.
+Plans to support other protocols and switching instead of routing are being made.
+(Some code for IPv6 routing and switching is already present but nonfunctional.)
+When tinc knows
which type of frame it has read, it can also read the source and
destination address from it.
-Now it is time that the frame gets encrypted. Currently the only
+Now it is time that the frame gets encrypted. Currently the only
encryption algorithm available is blowfish.
@cindex encapsulating
+@cindex UDP
When the encryption is ready, time has come to actually transport the
-packet to the destination computer. We do this by sending the packet
-over an UDP connection to the destination host. This is called
+packet to the destination computer. We do this by sending the packet
+over an UDP connection to the destination host. This is called
@emph{encapsulating}, the VPN packet (though now encrypted) is
encapsulated in another IP datagram.
When the destination receives this packet, the same thing happens, only
-in reverse. So it does a decrypt on the contents of the UDP datagram,
+in reverse. So it does a decrypt on the contents of the UDP datagram,
and it writes the decrypted information to its own ethertap device.
+To let the kernel on the receiving end accept the packet, the destination MAC
+address must match that of the tap interface. Because of the routing nature
+of tinc, ARP is not possible. tinc solves this by always overwriting the
+destination MAC address with fe:fd:0:0:0:0. That is also the reason why you must
+set the MAC address of your tap interface to that address.
+
@c ==================================================================
@node The Meta-connection, , Protocol Preview, The Connection
@subsection The meta-connection
-Having only an UDP connection available is not enough. Though suitable
+Having only an UDP connection available is not enough. Though suitable
for transmitting data, we want to be able to reliably send other
-information, such as routing and encryption information to somebody.
+information, such as routing and session key information to somebody.
+@cindex TCP
TCP is a better alternative, because it already contains protection
against information being lost, unlike UDP.
-So we establish two connections. One for the encrypted VPN data, and one
-for other information, the meta-data. Hence, we call the second
-connection the meta-connection. We can now be sure that the
+So we establish two connections. One for the encrypted VPN data, and one
+for other information, the meta-data. Hence, we call the second
+connection the meta-connection. We can now be sure that the
meta-information doesn't get lost on the way to another computer.
@cindex data-protocol
@cindex meta-protocol
Like with any communication, we must have a protocol, so that everybody
-knows what everything stands for, an how he should react. Because we
-have two connections, we also have two protocols. The protocol used for
+knows what everything stands for, and how she should react. Because we
+have two connections, we also have two protocols. The protocol used for
the UDP data is the ``data-protocol,'' the other one is the
``meta-protocol.''
The reason we don't use TCP for both protocols is that UDP is much
-better for encapsulation, even while it is less reliable. The real
+better for encapsulation, even while it is less reliable. The real
problem is that when TCP would be used to encapsulate a TCP stream
that's on the private network, for every packet sent there would be
-three ACK's sent instead of just one. Furthermore, if there would be
+three ACKs sent instead of just one. Furthermore, if there would be
a timeout, both TCP streams would sense the timeout, and both would
-start resending packets.
+start re-sending packets.
@c ==================================================================
@node Security, , The Connection, Technical information
@section About tinc's encryption and other security-related issues.
-@cindex tinc
+@cindex TINC
@cindex Cabal
tinc got its name from ``TINC,'' short for @emph{There Is No Cabal}; the
-alleged Cabal was/is an organization that was said to keep an eye on the
-entire Internet. As this is exactly what you @emph{don't} want, we named
+alleged Cabal was/is an organisation that was said to keep an eye on the
+entire Internet. As this is exactly what you @emph{don't} want, we named
the tinc project after TINC.
@cindex SVPN
But in order to be ``immune'' to eavesdropping, you'll have to encrypt
-your data. Because tinc is a @emph{Secure} VPN (SVPN) daemon, it does
+your data. Because tinc is a @emph{Secure} VPN (SVPN) daemon, it does
exactly that: encrypt.
+tinc uses blowfish encryption in CBC mode and a small amount of salt
+at the beginning of each packet to make sure eavesdroppers cannot get
+any information at all from the packets they can intercept.
-This chapter is a mixture of ideas, reasoning and explanation, please
-don't take it too serious.
+@cindex authentication
+Another important part is the authentication done prior to allowing other
+tinc daemons to connect. This is done by a challenge/response handshake
+involving RSA encryption.
+The details of the authentication can be found in a file called @file{doc/SECURITY2}
+in the source of tinc.
-@menu
-* Key Types::
-* Key Management::
-* Authentication::
-* Protection::
-@end menu
-
-@c ==================================================================
-@node Key Types, Key Management, Security, Security
-@subsection Key Types
-@c FIXME: check if I'm not talking nonsense
-
-There are several types of encryption keys. Tinc uses two of them,
-symmetric private keypairs and public/private keypairs.
-
-Public/private keypairs are used in public key cryptography. It enables
-someone to send out a public key with which other people can encrypt their
-data. The encrypted data now can only be decrypted by the person who has
-the private key that matches the public key. So, a public key only allows
-@emph{other} people to send encrypted messages to you. This is very useful
-in setting up private communications channels. Just send out your public key
-and other people can talk to you in a secure way. But how can you know
-the other person is who he says he is?
-
-For authentication itself tinc uses symmetric private keypairs, referred
-to as a passphrase. The identity of each tinc daemon is defined by it's
-passphrase (like you can be identified by your social security number).
-Every tinc daemon that is allowed to connect to you has a copy of your
-passphrase (hence symmetrical).
-
-It would also be possible to use public/private keypairs for authentication,
-so that you could shout out your public key and don't need to keep it
-secret (like the passphrase you would have to send to someone else). Also,
-no one else has to know a private key from you.
-Both forms have their pros and cons, and at the moment tinc just uses passphrases
-(which are computationaly more efficient and perhaps in some way more
-secure).
-
-@c ==================================================================
-@node Key Management, Authentication, Key Types, Security
-@subsection Key Management
-@c FIXME change for the current protocol
-
-@cindex Diffie-Hellman
-You can't just send a private encryption key to your peer, because
-somebody else might already be listening to you. So you'll have to
-negotiate over a shared but secret key. One way to do this is by using
-the ``Diffie-Hellman key exchange'' protocol
-(@uref{http://www.rsa.com/rsalabs/faq/html/3-6-1.html}). The idea is as
-follows.
-
-You have two participants A and B that want to agree over a shared
-secret encryption key. Both parties have some large prime number p and a
-generator g. These numbers may be known to the outside world, and hence
-may be included in the source distribution.
-
-@cindex secret key
-Both parties then generate a secret key. A generates a, and computes g^a
-mod p. This is then sent to B; while B computes g^b mod p, and transmits
-this to A, b being generated by B. Both a and b must be smaller than
-p-1.
-
-Both parties then calculate g^ab mod p = k. k is the new, shared, but
-still secret key.
-
-To obtain a key k of a sufficient length (128 bits in our vpnd), p
-should be 2^129-1 or more.
-
-
-@c ==================================================================
-@node Authentication, Protection, Key Management, Security
-@subsection Authentication
-@c FIXME: recheck
-
-@cindex man-in-the-middle attack
-Because the Diffie-Hellman protocol is in itself vulnerable to the
-``man-in-the-middle attack,'' we should introduce an authentication
-system.
-
-We will let A transmit a passphrase that is also known to B encrypted
-with g^a, before A sends this to B. This way, B can check whether A is
-really A or just someone else.
-B will never receive the real passphrase though, because it was
-encrypted using public/private keypairs. This way there is no way an
-imposter could steal A's passphrase.
-
-@cindex passphrase
-@c ehrmz... but we only use 1024 bits passphrases ourselves? [guus]
-This passphrase should be 2304 bits for a symmetric encryption
-system. But since an asymmetric system is more secure, we could do with
-2048 bits. This only holds if the passphrase is very random.
-
-These passphrases could be stored in a file that is non-readable by
-anyone else but root; e.g. @file{/etc/tinc/passphrases} with UID 0
-and permissions mode 700.
-
-The only thing that needs to be taken care of is how A can securely send
-a copy of it's passphrase to B if B doesn't have it yet. This could be
-done via mail with PGP, but you should be really convinced of the
-identity of the person who owns the email address you are sending this to.
-Swapping floppy disks in real life might be the best way to do this!
-
-
-@c ==================================================================
-@node Protection, , Authentication, Security
-@subsection Protecting your data
-
-Now we have securely hidden our data. But a malicious cracker may still
-bother you by randomly altering the encrypted data he intercepts.
-
-@c FIXME what the hell is this all about? remove? IT
@c ==================================================================
@node About us, Concept Index, Technical information, Top
@menu
-* Contact Information::
-* Authors::
+* Contact Information::
+* Authors::
@end menu
@node Contact Information, Authors, About us, About us
@section Contact information
-tinc's main page is at @url{http://tinc.nl.linux.org/},
+@cindex website
+tinc's website is at @url{http://tinc.nl.linux.org/},
this server is located in the Netherlands.
-We have an IRC channel on the Open Projects IRC network. Connect to
+@cindex IRC
+We have an IRC channel on the Open Projects IRC network. Connect to
@uref{http://openprojects.nu/services/irc.html, irc.openprojects.net},
and join channel #tinc.
@item Ivo Timmermans (zarq) (@email{itimmermans@@bigfoot.com})
Main coder/hacker and maintainer of the package.
-@item Guus Sliepen (guus)
+@item Guus Sliepen (guus) (@email{guus@@sliepen.warande.net})
Originator of it all, co-author.
-@item Wessel Dankers (Ubiq)
-General obfuscater of the code.
+@item Wessel Dankers (Ubiq) (@email{wsl@@nl.linux.org})
+For the name `tinc' and various suggestions.
@end table
-Thank you's to: Dekan, Emphyrio, vDong
-
-Greetings to: braque, Fluor, giggles, macro, smoke, tribbel
+We have received a lot of valuable input from users. With their help,
+tinc has become the flexible and robust tool that it is today. We have
+composed a list of contributions, in the file called @file{THANKS} in
+the source distribution.
@c ==================================================================
@c ==================================================================
@contents
@bye
-
projects / tinc / blobdiff