This is the info manual for @value{PACKAGE} version @value{VERSION}, a Virtual Private Network daemon.
-Copyright @copyright{} 1998-2011 Ivo Timmermans,
+Copyright @copyright{} 1998-2012 Ivo Timmermans,
Guus Sliepen <guus@@tinc-vpn.org> and
Wessel Dankers <wsl@@tinc-vpn.org>.
@vskip 0pt plus 1filll
This is the info manual for @value{PACKAGE} version @value{VERSION}, a Virtual Private Network daemon.
-Copyright @copyright{} 1998-2011 Ivo Timmermans,
+Copyright @copyright{} 1998-2012 Ivo Timmermans,
Guus Sliepen <guus@@tinc-vpn.org> and
Wessel Dankers <wsl@@tinc-vpn.org>.
both IPv4 and IPv6 or just IPv6 listening sockets will be created.
@cindex BindToAddress
-@item BindToAddress = <@var{address}> [experimental]
+@item BindToAddress = <@var{address}> [<@var{port}>] [experimental]
If your computer has more than one IPv4 or IPv6 address, tinc
will by default listen on all of them for incoming connections.
Multiple BindToAddress variables may be specified,
in which case listening sockets for each specified address are made.
+If no @var{port} is specified, the socket will be bound to the port specified by the Port option,
+or to port 655 if neither is given.
+To only bind to a specific port but not to a specific address, use "*" for the @var{address}.
+
This option may not work on all platforms.
@cindex BindToInterface
This option may not work on all platforms.
+@cindex Broadcast
+@item Broadcast = <yes | no> (yes) [experimental]
+When disabled, tinc will drop all broadcast and multicast packets, in both router and switch mode.
+
@cindex ConnectTo
@item ConnectTo = <@var{name}>
Specifies which other tinc daemon to connect to on startup.
tinc won't try to connect to other daemons at all,
and will instead just listen for incoming connections.
+@cindex DecrementTTL
+@item DecrementTTL = <yes | no> (no)
+When enabled, tinc will decrement the Time To Live field in IPv4 packets, or the Hop Limit field in IPv6 packets,
+before forwarding a received packet to the virtual network device or to another node,
+and will drop packets that have a TTL value of zero,
+in which case it will send an ICMP Time Exceeded packet back.
+
+Do not use this option if you use switch mode and want to use IPv6.
+
@cindex Device
@item Device = <@var{device}> (@file{/dev/tap0}, @file{/dev/net/tun} or other depending on platform)
The virtual network device to use.
Packets received for the local node are written to the raw socket.
However, at least on Linux, the operating system does not process IP packets destined for the local host.
+@cindex multicast
+@item multicast
+Open a multicast UDP socket and bind it to the address and port (separated by spaces) and optionally a TTL value specified using @var{Device}.
+Packets are read from and written to this multicast socket.
+This can be used to connect to UML, QEMU or KVM instances listening on the same multicast address.
+Do NOT connect multiple tinc daemons to the same multicast address, this will very likely cause routing loops.
+Also note that this can cause decrypted VPN packets to be sent out on a real network if misconfigured.
+
@cindex UML
@item uml (not compiled in by default)
Create a UNIX socket with the filename specified by
it can be used to change the way packets are interpreted:
@table @asis
-@item tun (BSD only)
+@item tun (BSD and Linux)
Set type to tun.
Depending on the platform, this can either be with or without an address family header (see below).
@cindex tunnohead
-@item tunnohead (BSD only)
+@item tunnohead (BSD)
Set type to tun without an address family header.
Tinc will expect packets read from the virtual network device to start with an IP header.
On some platforms IPv6 packets cannot be read from or written to the device in this mode.
@cindex tunifhead
-@item tunifhead (BSD only)
+@item tunifhead (BSD)
Set type to tun with an address family header.
Tinc will expect packets read from the virtual network device
to start with a four byte header containing the address family,
followed by an IP header.
This mode should support both IPv4 and IPv6 packets.
-@item tap (BSD only)
+@item tap (BSD and Linux)
Set type to tap.
Tinc will expect packets read from the virtual network device
to start with an Ethernet header.
Under Windows, this variable is used to select which network interface will be used.
If you specified a Device, this variable is almost always already correctly set.
+@cindex LocalDiscovery
+@item LocalDiscovery = <yes | no> (no) [experimental]
+When enabled, tinc will try to detect peers that are on the same local network.
+This will allow direct communication using LAN addresses, even if both peers are behind a NAT
+and they only ConnectTo a third node outside the NAT,
+which normally would prevent the peers from learning each other's LAN address.
+
+Currently, local discovery is implemented by sending broadcast packets to the LAN during path MTU discovery.
+This feature may not work in all possible situations.
+
@cindex Mode
@item Mode = <router|switch|hub> (router)
This option selects the way packets are routed to other daemons.
but will default to the configuration directory (you can use the -c or -n option
in combination with -K). After that, tinc will quit.
+@item -o, --option=[@var{HOST}.]@var{KEY}=@var{VALUE}
+Without specifying a @var{HOST}, this will set server configuration variable @var{KEY} to @var{VALUE}.
+If specified as @var{HOST}.@var{KEY}=@var{VALUE},
+this will set the host configuration variable @var{KEY} of the host named @var{HOST} to @var{VALUE}.
+This option can be used more than once to specify multiple configuration variables.
+
@item -L, --mlock
Lock tinc into main memory.
This will prevent sensitive data like shared private keys to be written to the system swap files/partitions.
projects / tinc / blobdiff