There are two lzo compression levels.

[tinc] / doc / tinc.conf.5

diff --git a/doc/tinc.conf.5 b/doc/tinc.conf.5
index 9ac1575..ad4fa1d 100644 (file)
--- a/doc/tinc.conf.5
+++ b/doc/tinc.conf.5
@@ -1,8 +1,8 @@
-.Dd 2002-02-06
+.Dd 2002-04-09
 .Dt TINC.CONF 5
 .\" Manual page created by:
-.\" Ivo Timmermans <itimmermans@bigfoot.com>
-.\" Guus Sliepen <guus@sliepen.warande.net>
+.\" Ivo Timmermans <ivo@o2w.nl>
+.\" Guus Sliepen <guus@sliepen.eu.org>
 .Sh NAME
 .Nm tinc.conf
 .Nd tinc daemon configuration
@@ -100,12 +100,19 @@ If you leave it out, remember to replace it with at least one space character.
 Here are all valid variables, listed in alphabetical order.
 The default value is given between parentheses.
 .Bl -tag -width indent
-.It Va AddressFamily Li = ipv4 | ipv6 | any Po ipv4 Pc Bq experimental
+.It Va AddressFamily Li = ipv4 | ipv6 | any Pq any
 This option affects the address family of listening and outgoing sockets.
 If
 .Qq any
 is selected, then depending on the operating system both IPv4 and IPv6 or just
 IPv6 listening sockets will be created.
+.It Va BindToAddress Li = Ar address Bq experimental
+If your computer has more than one IPv4 or IPv6 address,
+.Nm tinc
+will by default listen on all of them for incoming connections.
+It is possible to bind only to a single address with this variable.
+.Pp
+This option may not work on all platforms.
 .It Va BindToInterface Li = Ar interface Bq experimental
 If your computer has more than one network interface,
 .Nm tinc
@@ -129,7 +136,7 @@ If you don't specify a host with
 .Nm tinc
 won't try to connect to other daemons at all,
 and will instead just listen for incoming connections.
-.It Va Device Li = Ar device Po /dev/tap0 or /dev/misc/net/tun Pc
+.It Va Device Li = Ar device Po /dev/tap0 or /dev/net/tun Pc
 The virtual network device to use.
 .Nm tinc
 will automatically detect what kind of device it is.
@@ -230,7 +237,8 @@ Furthermore, specifying
 will turn off packet encryption.
 .It Va Compression Li = Ar level Pq 0
 This option sets the level of compression used for UDP packets.
-Possible values are 0 (off), 1 (fast) and any integer up to 9 (best).
+Possible values are 0 (off), 1 (fast zlib) and any integer up to 9 (best zlib),
+10 (fast lzo) and 11 (best lzo).
 .It Va Digest Li = Ar digest Pq sha1
 The digest algorithm used to authenticate UDP packets.
 Any digest supported by OpenSSL is recognised.
@@ -264,7 +272,7 @@ the above two options then are not necessary.
 Either the PEM format is used, or exactly one of the above two options must be specified
 in each host configuration file,
 if you want to be able to establish a connection with that host.
-.It Va Subnet Li = Ar address Ns Op Li / Ns Ar masklength
+.It Va Subnet Li = Ar address Ns Op Li / Ns Ar prefixlength
 The subnet which this tinc daemon will serve.
 .Nm tinc
 tries to look up which other daemon it should send a packet to by searching the appropriate subnet.
@@ -276,7 +284,7 @@ variables can be specified.
 .Pp
 Subnets can either be single MAC, IPv4 or IPv6 addresses,
 in which case a subnet consisting of only that single address is assumed,
-or they can be a IPv4 or IPv6 network address with a masklength.
+or they can be a IPv4 or IPv6 network address with a prefixlength.
 Shorthand notations are not supported.
 For example, IPv4 subnets must be in a form like 192.168.1.0/24,
 where 192.168.1.0 is the network address and 24 is the number of bits set in the netmask.